Skip to main content

Find the next available technician and book an appointment

Schedule tasks without putting customers on hold. View available technicians, choose a time slot, and book the appointment on the spot.

S
Written by Stacey Bray

Setup

You will need the following permissions in your security group:

  • Can create and update appointments.

  • Can create and update tasks.

Click here to learn about permissions and security groups.

To see your technicians' live locations on the map, the Telemetry extension needs to be enabled for your workspace. Without it, the map still works, but places technicians using their recent activity on a task.


How to open the next available technician scheduler for a task

The next available technician scheduler opens in a window called Schedule task, already filtered to the task you are booking. You can reach it two ways:

  • New task — when creating a callout or repair task, click Find Next Available Tech instead of Create. The task is created and the Schedule task window opens straight away.

  • Existing task — open the task, expand the Schedule card on the right and click + Schedule appointment.

If the task already has a primary technician, their name is pre-filled in the Name filter so they are the first technician you see.

Tip: The window shows today first. The map sits at the top with a date selector in its top right corner, the filters sit below it, and each technician has their own row underneath.


How to narrow down the technicians

A row of filters sits above the technician list. Use them to cut the list down to the people who can actually do the job.

1. Use the filters to narrow the list:

  • Branch — shown if your workspace uses branches. Starts on the property's branch.

  • Service group

  • Zone — shown if your workspace uses zones.

  • Accreditation — shown if your workspace uses accreditations. Starts on any accreditations the task requires.

  • Name — type part of a technician's name. Starts on the task's primary technician, if it has one.

2. Check the count above the technician list. It shows how many technicians match, for example how many are shown out of the total.

3. Click Clear next to the count to remove your filters and see everyone again.The list shows 10 technicians at a time. When more technicians match than are shown, click Show more to see up to 30.

How technicians are ordered

Technicians are listed so the most likely choice is at the top:

  1. The property's default technician (house icon), or the default for the task's service group.

  2. Technicians who have attended this property before. A label under their name shows the category of their last task there and how long ago it was; hover over it for the task reference.

  3. Technicians who already have appointments that day.

  4. Everyone else, in alphabetical order.

A yellow warning triangle beside a name means the technician may not be a good fit. Hover over it to see why: they are missing an accreditation the task needs, an accreditation will have expired by the day you are booking, or they are not in the property's zone.


How to find the next free time slot

Each technician has their own row running across the day, so you can compare everyone's availability at a glance.

1. Look along each technician's row. Their existing appointments appear as grey blocks showing the task reference and how long it runs. Light green gaps are free time.

2. The length of the job comes from the task's On-site time required, or one hour if none is set.

3. Time outside a technician's working hours is shaded, so you can see when they start and finish.

4. Use the arrows at the left and right edges of the timeline to show earlier or later hours.

5. Hover over a free gap. A preview of the appointment follows your cursor and shows its start and end time, so you can see exactly where the job would land.

Check another day

If nobody has space today, move to another day without leaving the window. The date selector sits in the top right corner of the map.

1. Click the right arrow to go to the next day, or the left arrow to go back one day.

2. Or click the date in the middle to open a calendar and jump to any day.

3. The technician rows update to show that day's appointments and free time.

Note: You can't select a day before today. If you had already picked a time slot, it is cleared when you change day, so pick it again on the new day.


How to see where your technicians are

The map at the top of the window helps you pick who is closest. A red pin marks the property for the task. Each technician's appointments for the day are drawn as a coloured route with a dot at each stop, in the same colour as their avatar.

1. Hover over a technician's name in the list to highlight their route on the map. Everyone else fades into the background.

2. When you are viewing today, each technician appears on the map as an avatar at their current location.

3. Find the avatar nearest the red pin, then check that technician's row for a free gap.

Live locations with telemetry

If Telemetry is enabled for your workspace, avatars show each technician's last reported location and pulse to show they are live. A faint trail behind each avatar shows where they have been over the last hour, so you can see which way they are heading. Hover over an avatar to see when the technician last reported in.

Without telemetry, technician locations are based on their recent activity on a task. The avatar shows for 2 hours after activity is recorded, then disappears until there is new activity.

Note: Locations only show for today. An avatar disappears if a technician's location hasn't been updated recently, and technicians who haven't reported in won't appear on the map.

See where technicians will be later in the day

Use the See tech location by time slider below the filters to look ahead.

1. Drag the slider along the day. A line follows it across every technician's row, and the time shows above it.

2. Watch the map. Avatars move to each technician's scheduled appointment address at that time. These are scheduled locations, not live ones.

3. Click the X next to the slider to clear your selection and go back to live locations.


How to book the appointment

1. Click a light green gap on the technician's row. The appointment is placed at the spot you clicked and the technician is selected. It shows the task reference and how long it runs.

2. Fine-tune the time if you need to:

  • Drag the appointment left or right to move it.

  • Drag its right-hand edge to make it shorter or longer.

  • Both snap to 15-minute steps.

3. Select more technicians if the job needs a team. Click each technician's name to select or deselect them, then click a free gap for any of them. All selected technicians are booked for the same time.

4. If the task has no primary technician, the first technician you select becomes the primary. To choose a different one, click the star beside their name.

5. Complete the appointment details that appear below the technician list:

  • Category — choose an appointment category.

  • Add an internal note — a note visible to your team and to technicians on the mobile app.

  • Add a note for the client — appears under the appointment in the default appointment notification email.

6. Click Create appointment.

The appointment is added to the task as Scheduled and shows on each selected technician's calendar.

Tip: Click Hide at the end of the details row to tuck it away while you compare technicians. Your category and notes are kept. Click the blue X beside the technician's name to remove the slot and start again.


What to do when nobody has space

For an urgent job, you may need to move existing bookings to make room, so use the full Scheduler for this.

1. Click Continue in scheduler in the top right of the window.

2. The full Scheduler opens, filtered to your task. Any slot, technicians, category and notes you had already chosen come with you as a draft appointment, so you don't lose your work.

If you would rather book first and adjust afterwards, click Create & view in scheduler at the bottom of the window instead. The appointment is created and then opened in the Scheduler.

See Schedule tasks and send notifications for more on working in the Scheduler.


Recommended steps

Did this answer your question?